New request Please help me with a stage 1 for BMW 435xd

Post #1

B Online now

bmwx

Stock Member

Spain
Joined
21.11.2026
Messages
6
Reactions
0
Location
Spain
Vehicle / engine
BMW 435xd
Reading tool / method (if known)
Ktag master
Hello,
I am looking for a clean Stage 1+ (~385–395 HP / ~760–780 Nm) + Full EGR OFF including at idle (DPF ON) built strictly from my attached original file (read with Alientech KTAG Master, Plug-in 667, MICRO TC1797, 4,194,304 bytes).
Hardware upgrades installed on the car:
  • Wagner Tuning Competition Evo 2 Intercooler
  • xHP Flashtool installed on the ZF 8HP70 transmission (gearbox torque limiters raised)


  • Factory DPF still installed and active
Important calibration requirements:
  1. Please modify ONLY my attached SW 547776 (O_7ETN0-000036C7-001) original binary — do not substitute a file from another chassis (F10/F15/F30).
  2. Full EGR OFF (0% closed across all RPM/load including idle via hysteresis maps, EGR plug connected, air-mass plausibility 24CE00/290900 handled properly without altering the physical MAF sensor linearization curve) while keeping DPF 100% active and automatic DPF regeneration working normally.
  3. Please keep wideband Lambda (1) feedback active, stock idle fueling (~5.1 mg/stk) untouched, and stock throttle-body behavior so there is zero rich idle exhaust smell.
  4. Keep safe EGT limits (≤ 850°C pre-turbo) and safe Bosch CP4 rail pressure limits (≤ 2,100–2,150 bar).
Thank you!
 
Ratings and Reviews
Total ratings: 0

Post #2

Bin Online now

Bin

Administrator
Antarctica
Joined
03.05.2025
Messages
2,436
Reactions
122,803
Location
Antarctica
Hello, you didn't attach it

  1. Please modify ONLY my attached SW 547776 (O_7ETN0-000036C7-001) original binary — do not substitute a file from another chassis (F10/F15/F30).
 

Post #3

B Online now

bmwx

Stock Member

Spain
Joined
21.11.2026
Messages
6
Reactions
0
Location
Spain
Original file
Hello, you didn't attach it

  1. Please modify ONLY my attached SW 547776 (O_7ETN0-000036C7-001) original binary — do not substitute a file from another chassis (F10/F15/F30).
I thought I did. Thank you for checking!
I tried a few times to attach the file but I cannot see it after
 
Last edited:

Post #4

B Online now

bmwx

Stock Member

Spain
Joined
21.11.2026
Messages
6
Reactions
0
Location
Spain
The original Micro file
 

Post #5

Bin Online now

Bin

Administrator
Antarctica
Joined
03.05.2025
Messages
2,436
Reactions
122,803
Location
Antarctica
The original Micro file
Original file

I thought I did. Thank you for checking!
I tried a few times to attach the file but I cannot see it after
It would have been better to pack it into a ZIP archive, as the forum doesn't support all file extensions for attachments.

Please try attaching it again. I've added support for that file extension.
 

Post #7

B Online now

bmwx

Stock Member

Spain
Joined
21.11.2026
Messages
6
Reactions
0
Location
Spain
It would have been better to pack it into a ZIP archive, as the forum doesn't support all file extensions for attachments.

Please try attaching it again. I've added support for that file extension.
Thank you! It worked!
 

Post #8

Bin Online now

Bin

Administrator
Antarctica
Joined
03.05.2025
Messages
2,436
Reactions
122,803
Location
Antarctica
A staff member has published an offer for this request.
 
Activity
So far there's no one here