Welcome to BinUnlock – Introduce Yourself Here!
- Thread starter Bin
- Start date
Post #82
- Joined
- 23.02.2026
- Messages
- 2
- Reactions
- 0
- Location
- Australia
hi i have joined as with how complex cars are getting i need all the assistance i can get, my wifes tiguan had an ac compressor sieze,it only broke rhe exhaust rockers,but after pulling the head to ensure the valves were ok one of the needle rollers wound up inside the intake port of nymber 2 cylinder, so when i went to start it after thinking everything was ok it started for all of about 30 seconds,pulled the head again as turning it over by hand it was locking up now,decided to buy a used low kilometer engine complete, put it in it would crank but not fire, found son in law who was helping had put main earth to positive, i sent the ecu off to be checked it had burnt tracks, also discovered wiring on my original motor was slightly different to the new one although the same engine code, the original engine had the dpf sensor wiring in the engine harness the motor i bought did not, as the wife loves the car and is a perfect fit for her to get into and out of i bought a running car that was only 6 months older and thought this one runs i will just pull all the running gear and put in ours (as the running one was out of registration and needed a windscreen) only to find the dpf on the new car went to the same terminal on the ecu but went through the body wiring harness and i was not going to pull it apart to swap the full body harness over, so i now have better panels to paint and put on the newer one if she ever lets me get near it again. it took 26 months to get her back in a car she loves
Post #83
Post #84
Post #85
Post #86
- Joined
- 13.02.2026
- Messages
- 5
- Reactions
- 2
- Location
- United States
Awesome site! Stumbled upon it looking for a kеуg** and it's been quite the surprise to see the other software available.
I'm an electrician, programmer, and locksmith in the states looking to get into reverse engineering as well.
I'm an electrician, programmer, and locksmith in the states looking to get into reverse engineering as well.
Post #87
Post #88
- Joined
- 02.03.2026
- Messages
- 3
- Reactions
- 6
- Location
- Romania
Hi to all my name is Andrei l am from România.l work as automechanic and make chiptuning
Post #89
Post #90
Post #91
Post #92
Post #93
- Joined
- 25.02.2026
- Messages
- 1
- Reactions
- 1
- Location
- United States
I'm learning every day, as I think we all should be! I'm so happy to find a great site like this, with such a fantastic community of people, helping people. I have been reading through so many useful posts, and everyone is so willing to help solve other people?! This is rarely seen online anymore, but exactly how it is supposed to be! I plan to learn a lot here and I hope to be able to offer assistance from some of my unique experiences at some point. Well done, Everyone!
Post #94
Post #95
- Joined
- 11.03.2026
- Messages
- 22
- Reactions
- 4
- Location
- Romania
Hi everyone,
My name is Marius. I am from Romania.
Cars are my main passion.
Most of the time I work with ECUs, electronics, wiring issues, sensors, injectors and different control modules. I also read and analyze ECU files and I am
I joined this forum to learn from other members, share experience and discuss technical problems related to cars.
Thank you and I’m glad to be here.
My name is Marius. I am from Romania.
Cars are my main passion.
Most of the time I work with ECUs, electronics, wiring issues, sensors, injectors and different control modules. I also read and analyze ECU files and I am
I joined this forum to learn from other members, share experience and discuss technical problems related to cars.
Thank you and I’m glad to be here.
Post #96
Hello. I'm from Poland, from the Podkarpackie Voivodeship. I'm an amateur and wanted to learn something about coding and programming. Best regards.Welcome to BinUnlock!
If you're new here, write a short message so we can get to know you
No pressure, but we'd love to hear:
Your name (or nickname)
Where are you from?
Which vehicles or ECUs you work with
Which tools you use (KESS, Autotuner, PCMFlash, etc.)
What you want to learn or what you want to offer
Do you have anything interesting about yourself (a car project, hobby, side gig?)
---
###Example:
Hi!
I'm Alex from Poland. I've been tuning VAG group cars for over 5 years, mainly using WinOLS and Autotuner.
I love tinkering with MED17 ECUs and am always happy to exchange ideas or files.
I'm a big fan of old BMWs and am currently working on a turbocharged E36 project.
Cheers!
---
Let's build a strong, helpful community.
Feel free to reply to others and say "hello"
Post #97
- Joined
- 15.03.2026
- Messages
- 1
- Reactions
- 0
- Location
- United States
Hey,Welcome to BinUnlock!
If you're new here — drop a quick introduction so we can get to know you
No pressure, but we’d love to hear:
---
###
Hey!
I'm Alex from Poland. Been tuning VAG group cars for 5+ years, mainly with WinOLS and Autotuner.
Love messing with MED17 ECUs and always down to trade ideas or files.
Big fan of retro BMWs and currently working on a turbo E36 project.
Cheers!
---
Let’s build a strong, helpful community.
Feel free to reply to others and say hi
I'm Joel from Colorado new to all this have many diesel vehicles and always delete EGR, DEF, DPF want to learn how to use tune files instead of paying a big amount each time to someone else. If someone could possibly help me with this I am willing to pay as I am super confused about how to use all this.
Thank you
Post #98
- Bking Nickname related to the Suzuki motorcycle
- FRANCE
- I am discovering for the moment
- What tools do you use (KESS/KTAG)
- learning from your knowledge and help
- thank you for all your shares and very presentable site, well done
Post #99
Post #100
Activity
So far there's no one here